Flandria Forum Flandria Forum
Liefhebbers van Flandria/Superia/Avaros en Claeys-Bromfietsen uit Belgie en Nederland
 
 FAQFAQ   ZoekenZoeken   GebruikerslijstGebruikerslijst   GebruikersgroepenGebruikersgroepen   RegistrerenRegistreren 
 ProfielProfiel   Log in om je privéberichten te bekijkenLog in om je privéberichten te bekijken   InloggenInloggen 

Flandria Penny S

 
Nieuw onderwerp plaatsen   Reageren    Flandria Forum -> English
Vorige onderwerp :: Volgende onderwerp  
Auteur Bericht
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 24-10-2019 18:15:29    Onderwerp: Flandria Penny S Reageren met citaat

Hello,

my name is Tobi from Frankfurt, Germany.
I visited Belgium recently and bought a Flandria Penny S from 1977 because I liked the style of this brommer.

Now I want to drive it, but it doesn't run properly. I think the carburetor is broken. It's a Encarwi Model S23F.
Now my question: Does someone here have a good complete carburetor of this type, which he wants to sell and is willing to send it to Germany?

Many thanks
Tobi
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Rekord
Flandria-Koning


Geregistreerd op: 24 Jan 2012
Berichten: 1465

BerichtGeplaatst: 25-10-2019 09:45:04    Onderwerp: Reageren met citaat

Dear Tobi, Could you provide me some pictures of the carburettor? I have some spare parts available. Maybe you can repair it.
_________________
"Details maken de perfectie, maar perfectie is geen detail"
Terug naar boven
Profiel bekijken Stuur privébericht
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 25-10-2019 14:16:56    Onderwerp: Reageren met citaat



This is the only picture I currently have. I took it apart and cleaned it. It also seems to be complete apart from the air filter and air filter housing. As I had it apart, I noticed that the needle on top of the float was bent a little bit.

If you need more pictures, let me know.
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
daytona
Flandria-Koning


Geregistreerd op: 27 Mrt 2012
Berichten: 1136

BerichtGeplaatst: 27-10-2019 16:42:09    Onderwerp: Reageren met citaat

Hi Tobi and welcome to this forum.

the bent needle on the float surely is something to look after as this probably causes problems to stop allowing fuel in the carburettor and it probably starts leaking at one point?

I hope Rekord can help you out.

Please also share some pictures of your Flandria Penny. There's probably just a small amount of Flandria's in Germany. I was at Veterama in Mannheim for several years and took a Flandria Polo to ride around there and got many looks and questions from people who never heard of or ever saw a Flandria before. I'm sure you'll get a lot of questions too like: 'where did you get that??' Very Happy
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Rekord
Flandria-Koning


Geregistreerd op: 24 Jan 2012
Berichten: 1465

BerichtGeplaatst: 30-10-2019 20:42:30    Onderwerp: Reageren met citaat

I will send you a private message.
_________________
"Details maken de perfectie, maar perfectie is geen detail"
Terug naar boven
Profiel bekijken Stuur privébericht
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 04-11-2019 13:30:40    Onderwerp: Reageren met citaat

Thanks for your message, Rekord.

I just can't send an answer, because the board gives an SQL Error back to me.

I've put my mail in my profile here, so that we can get in touch this way.

And I will share some pictures soon, but currently I don't have enough time to do so.
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 25-11-2019 14:06:50    Onderwerp: Reageren met citaat

So I have taken apart the carb and cleaned it again. It really seems like the float isn't working correctly because the needle is a little bit bent.

I have put it back together and the Flandria now starts and runs for about 10 sec, so I think that the engine doesn't get enough petrol. This could still be reason of the float not working, am I right?

Here are some pics of the carb:




Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
daytona
Flandria-Koning


Geregistreerd op: 27 Mrt 2012
Berichten: 1136

BerichtGeplaatst: 27-11-2019 13:21:32    Onderwerp: Reageren met citaat

You might want to check the bottom of the float chamber where the lower needle sits. If that small hole is clogged with dirt (a common problem which is often not noticed), it will not allow the floater to lower to a point sufficient enough to allow the required amount of fuel into the float chamber.
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 29-11-2019 19:19:31    Onderwerp: Reageren met citaat

I noticed that too. I think I have to put the carb in an ultrasonic bath, to get really all of the dirt out.

Do you have any other tips for tuning this particular type of carburettor?
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
daytona
Flandria-Koning


Geregistreerd op: 27 Mrt 2012
Berichten: 1136

BerichtGeplaatst: 06-12-2019 15:47:59    Onderwerp: Reageren met citaat

There's nothing much to tune or clean on these types of carburettor as there's no seperate idle circuit, choke circuit or needle in the throttle valve to adjust so they're very simple to adjust and clean. I presume you made sure that the gas runs sufficiantly from the tank itself?
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 17-12-2019 20:41:04    Onderwerp: Reageren met citaat

Yes, I got a new fuel tap and clear fuel line so I can see the fuel flow.

I noticed that a Piaggio Ciao carb has the same flange diametre, so maybe I can fit a new one of those... I have to try that idea in the holidays Smile
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
daytona
Flandria-Koning


Geregistreerd op: 27 Mrt 2012
Berichten: 1136

BerichtGeplaatst: 02-01-2020 08:40:45    Onderwerp: Reageren met citaat

They do fit the thread size but they have this sort of bent copper tube that might give you some trouble to fit it. You can use one from a Kreidler or Zündapp, they are more likely to fit without any issues.
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Schorsch
Flandria-Liefhebber


Geregistreerd op: 10 Okt 2019
Berichten: 7

BerichtGeplaatst: 15-06-2020 15:50:34    Onderwerp: Reageren met citaat

Finally I got it to run and drive! I bought an ultrasonic cleaner which cleaned the original carb like new. Then I had a problem with the choke, but now it is fixed.

Here is the requsted picture.

Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
daytona
Flandria-Koning


Geregistreerd op: 27 Mrt 2012
Berichten: 1136

BerichtGeplaatst: 15-06-2020 17:27:02    Onderwerp: Reageren met citaat

Looks good!
Terug naar boven
Profiel bekijken Stuur privébericht E-mail versturen
Berichten van afgelopen:   
Nieuw onderwerp plaatsen   Reageren    Flandria Forum -> English Tijden zijn in GMT + 1 uur
Pagina 1 van 1

 
Ga naar:  
Je mag geen nieuwe onderwerpen plaatsen in dit subforum
Je mag geen reacties plaatsen in dit subforum
Je mag je berichten niet bewerken in dit subforum
Je mag je berichten niet verwijderen in dit subforum
Je mag niet stemmen in polls in dit subforum


Wilt u geen reclame op dit forum en genieten van extra voordelen? Klik dan vlug hier voor meer informatie!
 

Powered by phpBB
immo op Realo
Maak snel, eenvoudig en gratis uw eigen forum: Gratis Forum